• Solas impeller - Kawasaki SXR 1500 / 160 148mm KGX-CD
  • Solas impeller - Kawasaki SXR 1500 / 160 148mm KGX-CD
  • Solas impeller - Kawasaki SXR 1500 / 160 148mm KGX-CD
  • Solas impeller - Kawasaki SXR 1500 / 160 148mm KGX-CD
  • Solas impeller - Kawasaki SXR 1500 / 160 148mm KGX-CD
1 5

SOLAS

Solas Impeller - Kawasaki SXR 1500 148MM

Solas Impeller - Kawasaki SXR 1500 148MM

KGX-CD-15/20

In stock

$315.93
Shipping calculated at checkout.
Impeller Pitch

Unlock the full potential of your 4-stroke SXR with the Solas Concord KGX impeller. Engineered with a larger blade area and an upgraded hub profile, the Concord pulls harder off the line and pushes higher on top, giving you noticeable gains in both acceleration and peak speed over the stock setup.

Built from high-strength stainless steel with a polished hub, every Concord impeller is precision machined for balance and durability under the abuse a standup demands. Solas's exclusive hub-end water seal reduces cavitation at the back of the hub, keeping the blades fully loaded and hooked up to clean water. A rubber nose cone is included for a clean, finished install.

The 15/20 pitch is the recommended setup for stock or lightly modified SXR 1500 / 160 engines at sea level. It loads the engine correctly for the factory rev range, maximizing top-end speed without pulling RPM out of the powerband.

Features

  • Fits 2017 and newer Kawasaki SXR 1500 / 160 4-stroke
  • Large blade area for stronger low-end thrust and higher top speed
  • High-strength stainless steel construction
  • Polished hub for reduced drag
  • Exclusive hub-end water seal to reduce cavitation
  • Rubber nose cone included
  • Fits 148mm diameter wear ring
  • Replaces OEM Part Number: 59255-3729

NOTE: Impeller Shaft Tool required for installation (sold separately).

Reported to fit the following Kawasaki PWC Models:

  • 2017 Kawasaki SXR 1500 / 160
  • 2018 Kawasaki SXR 1500 / 160
  • 2019 Kawasaki SXR 1500 / 160
  • 2020 Kawasaki SXR 1500 / 160
  • 2021 Kawasaki SXR 1500 / 160
  • 2022 Kawasaki SXR 1500 / 160
  • 2023 Kawasaki SXR 1500 / 160
  • 2024 Kawasaki SXR 1500 / 160
  • 2025 Kawasaki SXR 1500 / 160

Liability Disclaimer – Closed Course Use Only

Blowsion products are intended for closed course competition use only. These products are not designed, tested, or approved for use on public waterways or pollution-controlled vehicles.

Installation and operation of Blowsion components may affect the safety, emissions compliance, and legal status of your watercraft. Use of these products on public waterways may be a violation of federal, state, or local laws.

By purchasing and installing Blowsion products, the user assumes all responsibility and risk associated with their use, including but not limited to personal injury, property damage, or legal penalties.

Always follow proper safety procedures and consult with a qualified technician for installation.

Product Installation Disclaimer:

Warning:

When using electric or battery-operated tools inside the hull, ensure the area is well-ventilated and free of fumes. Failure to follow this precaution may result in fire, explosion, serious injury, or death.

Disconnect the battery before performing any installation or maintenance to prevent accidental ignition or electrical shock.

Allow the engine to cool completely before beginning installation.

No Smoking!

This kit is not designed for use on vehicles equipped with pollution control systems. Installing this kit on such vehicles may violate state or local laws

View full details